MCP Process(Pump Drive) - ISMATEC- 정량펌프 전문 레보딕스(주)

*ISMATEC제품 : Tubing pump / Tubing / Peristaltic pump *

ISMATEC의 강력한 PC-Programmable Dispensing Pump Drive를 소개해 드리겠습니다.

 

★ IP65-rate를 가지면서 programmable 가능한 Dispensing Pump
★ Microprocessor contoller로 정량이 보장 되는 Pump
★ Operating parameter를 4개 까지 저장가능
★ Flow rate와 volume Calibration(검교정) 가능
★ Dosing 및 Filling에 이상적인 Pump
★ 20개가 넘는 다양한 Pump-Head 장착 가능
★ 최대 24 Channel까지 동시 구동 가능
★ Ceramic piston Pump-Head까지 장착가능
★ 강력한 이송용 Pump
★ RS232 Controll 가능
★ Flow rate : 0.001 - 3700 ml/min

<Ordering Information>

Ordering Information

Order No. for this drive ISM 915

Interchangeable pump-heads

 

<Specification>

Flow rates	< 0.001 – 3700 ml/min (depending on mounted pump-head)
Channels	1 – 24 (depending on mounted pump-head)
Operating panel	- 7-button membrane key-pad - LED display
Memory	4 sets of operating parameters can be stored
Programming (similar to PLC)	4 individual command sequences programmed in a PC can be stored in  the pump. The user can run the programs using the pump as a stand-alone unit.
Operating modes	- pumping by drive speed (rpm) - pumping by flow rate (ml/min) - factory-set flow rates for all available tube sizes - dispensing by volume (ml) - dispensing by time (0.1s up to 999hrs) - dispensing by volume within a pre-set time - interval dispensing by volume with a pause - interval dispensing by time with a pause - setting the number of dispensing cycles - pause time setting (from 0.1s up to 999hrs) - roller back-steps for drip-free dispensing - reversible rotation direction
Calibrating function	- for flow rate (ml/min) - for dispensing volume (ml)
Speed	1 – 240 rpm
Speed setting	rpm, resolution 0.1 rpm
Speed control	closed loop control for pressure independent speed
RS232 interfaces	- RS232 "in"   - for operation controlling via PC - RS232 "out" - for cascading up to 8 pumps
Analog input	Speed control (0–5 or 0–10V / 0–20 or 4–20mA)
Analog output	Speed monitoring (0–10VDC or 0–7.2 kHz)
Digital input (TTL level)	Start/Stop, rotation direction, autostart, 2 universal inputs
Digital output (PWM)	2 universal outputs
Differential pressure	1.5 bar (21.7 psi) possible (depending on pump-head and tubing material); small tubing diameters may allow higher pressures
Motor type	DC motor
Power consumption	100 W
Power supply	100 – 230 VAC / 50 – 60 Hz
Protection rating	IP 65
Depth / Width / Height	220 x 155 x 260 mm (8 2/3" x 6 1/10" x 10 ¼") (without pump-head)
Weight	6.9 kg (16 lb) (without pump-head)
Accessories	- Progedit software (free download) - Driver for "LabView" software (free download) - Foot switch

 

레보딕스(주) TEL : 031-790-1907 FAX : 031-790-1908 www.revodix.co.kr  (홈페이지를 방문하시면 더 다양한 제품들을 만나보실 수 있으십니다~ Go Go)